Free shipping on orders over $35. See Details

Farmworks

Spray Tank Cleaner

Available exclusively at Tractor Supply Co.

Remove residue. Avoid cross contamination.

Remove chemical residues from your spray equipment safely and effectively with Spray Tank Cleaner. Flush all working parts regularly to optimize performance and prolong the life of your spray equipment. Eliminate cross contamination when switching chemicals and prevent unwanted results caused by hard-to-remove residues from chemicals such as 2,4-D and sulfonylureas.

Where to use:

In all working parts of your spray equipment.

When to use:

When swithcing chemicals.

How to use:

  1. Add 1/2 of the water needed based on the tank size
  2. Dissolve amount of Spray Tank Cleaner needed to clean tank as shown by Use Rate chart
  3. Add remaining amount of water
  4. Close valve to spray boom
  5. Agitate vigorously
  6. Open bypass valve and circulate solution through spraying system for 15 minutes
  7. Use hose or hand sprayer to thoroughly wash all internal tank parts
  8. Open spray boom valve and allow solution to flow through entire spray boom as well as nozzles
  9. Refill tank with water to the same rate as previously used with Spray Tank Cleaner to recirculate for 10 minutes and then flush through spray boom and nozzles. If changing chemicals, a second rinse is recommended with 25 gallons of water. 

USE RATE

Spray Tank Cleaner Amount of Water Tank Size
4 ounces 12.5 gallons 25 gallons
8 ounces 25 gallons 50 gallons
16 ounces 50 gallons 100 gallons
32 ounces 100 gallons 200 gallons

EXTRA PRECAUTIONS SHOULD BE FOLLOWED AFTER USING 2,4-D OR SIMILAR MATERIALS.

Hoses, rubber connections, pump and hand gun packing are more likely to retain 2,4-D than tank, boom or metal parts, equal attention should be given to the flushing of these. Many authorities recommend renewal of soft parts after using 2,4-D. However, if these are in good condition, Spray Tank Cleaner will clean them.

  1. Flush complete rig with plain water, inside and out
  2. Use as directed on label except allow Spray Tank Cleaner to remain in rig and hoses overnight
  3. Take liberal sample of second rinse from each section of boom and hand gun
  4. Sprinkle these samples on particularly susceptible plants such as tomato, cotton, etc. to determine if cleaning was sufficient. Period required to show 2,4-D varies with tem-perature and humidity. 48 hours is usually enough
  5. If tests show 2,4-D present replace hoses, pump packing, rubber connections, etc. and repeat entire process including test.

Precautions:

Wash hands thoroughly after handling. Wear eye protection.

Active Ingredients:

Sodium carbonate

Product Label:

Disclaimer:

It is a violation of Federal law to use this product in a manner inconsistent with its labeling. Read the entire label before each use. Use only according to label instructions.

See the complete label for specific use rates and detailed instructions.

Consult the Safety Data Sheet (SDS) for important safety information.

Advice

  1. Feed And Forage Composition

    Things that initially appear to be complex often seem simple once they have been explained and are understood. Perhaps a good example is the composition of livestock feeds and forages. Many of the numerous terms used in describing these components are not commonly used by the general public, which naturally [...]

  2. The Case For Testing Forage

    Only a relatively small percentage of livestock producers regularly test their hay or other stored feed. Some are probably just not aware of, or not well informed about, this service. Unfortunately, many others know about it but apparently don’t consider it important enough to take the time and expend the [...]

  3. Stockpiling Warm Season Grasses

    Less-than-optimum weather conditions, as well as the cost of fertilizer, fuel, and other production inputs are factors that often make it difficult for livestock producers to make a profit.  Providing  nutrition during times when pasture is not available is one of the costliest aspects of producing livestock, so it makes [...]

  4. PASTURES TELL A STORY

    A livestock producer learns a lot about a pasture over time by managing it, but that is not the only way to obtain information about a given field. Often, a great deal can be gained from simple observation, because various plants are more likely to become established and thrive under [...]

  5. KEY HAY STORAGE CONCEPTS

    Providing nutrition when little or no pasture forage is available constitutes the single largest expense associated with most livestock operations. In most cases, hay is the most logical type of stored feed to use. Generally, the less hay required, the greater the cost effectiveness of an operation, and how hay [...]