Free shipping on orders over $35. See Details

RM43

Total Vegetation Control

As low as $39.99
-
+

Serious Weed Control™ For Up To A Year!

RM43 is your solution for total vegetation control on bare ground or for spot control of brush, vines and more than 150 weeds. It kills existing weeds and prevents future growth on walkways, roadsides, fence lines and any place you want to keep free from invasive plants. 

RM43 Total Vegetation Control is a combination of two herbicides and a surfactant. Glyphosate kills the weeds and imazapyr prevents new growth. It is rainfast in two hours and there are no entry restrictions to sprayed areas for pets or people after the spray has dried.

How Much Do I Need?

   32-ounce 64-ounce 1-gallon 2.5-gallon
Total Vegetation Control: Treats up to 4,324 sq ft 8,648 sq ft 17,297 sq ft 43,243 sq ft
Spot Treatment: Makes up to 5 gal 10 gal 21 gal 53 gal

Where to use:

Roadsides Warehouse areas Brick walks
Curbs Fencerows Gravel paths
Sidewalks Around farm buildings and barns Farm premises
Driveways Agricultural uncultivated areas Vacant lots
Parking areas Farm yards For establishment and maintenance of wildlife openings

When to use:

Apply to bare ground or when weeds are present. If weeds are taller than six inches, mow or cut down weeds, remove debris and allow for 2 weeks of new growth before treatment.

If woody vines or brush is mowed or cut, wait until full leaf formation before treatment.

To prevent growth of weeds under asphalt driveways, play areas, tennis courts and parking areas, apply this product before laying surfacing materials. Treat area uniformly to maximize results. Re-treatment every 6 to 8 months may be necessary in areas of heavy rainfall.

How to use:

For Total Vegetation Control (Bare Ground)

Use hand-operated spray equipment such as backpack sprayers, pump-up sprayers or sprinkling cans, or ATV/tractor-mounted sprayers. Mix 7.4 fl. oz. (0.46 pints) of product with water to produce 1 to 10 gallons of spray solution. Optimum performance will be achieved by applying to actively growing weeds in early summer. Uniformly spray the mix over areas where total vegetation control and bare ground is desired. 7.4 fl. oz. of product in 1 to 10 gallons of spray solution should be applied to 1,000 square feet. Maximum application rate of this product is 2.5 gallons per acre per year (7.4 fl. oz. per 1,000 sq. ft. per year).

For Spot Control of Brush, Vines and Weeds

Use hand-operated spray equipment such as backpack sprayers, pump-up sprayers or sprinkling cans, or ATV/tractor-mounted sprayers. Mix 6 oz. of product per 1 gallon of spray solution. Thoroughly and uniformly spray foliage of woody plants to wet. For optimum performance:

  • Apply to actively growing brush, vines and weeds.
  • Woody brush and vines are controlled better in late summer and fall after fruit formation.
  • If woody vines and brush are mowed or cut, wait until full leaf formation before treatment.
  • Do not cut or mow brush, vines or perennial weeds for 2 months following treatment.
  • Maximum application rate of this product is 2.5 gallons per acre per year (7.4 fl. oz. per 1,000 sq. ft. per year).

Precautions:

  • Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application.
  • Do not enter or allow others to enter treated areas until sprays have dried.
  • Do not use on feed or food crops. Keep people and pets out of the area during application.
  • For any requirements specific to your state or tribe, consult the agency responsible for pesticide regulation.

Active Ingredients:

Glyphosate, isopropylamine salt 43.68%
Imazapyr, isopropylamine salt 0.78%
Other Ingredients 55.54%
Total 100.00%

Product Label:

Disclaimer:

It is a violation of Federal law to use this product in a manner inconsistent with its labeling. Read the entire label before each use. Use only according to label instructions.

See the complete label for specific use rates and detailed instructions.

Consult the Safety Data Sheet (SDS) for important safety information.

Advice

  1. Feed And Forage Composition

    Things that initially appear to be complex often seem simple once they have been explained and are understood. Perhaps a good example is the composition of livestock feeds and forages. Many of the numerous terms used in describing these components are not commonly used by the general public, which naturally [...]

  2. The Case For Testing Forage

    Only a relatively small percentage of livestock producers regularly test their hay or other stored feed. Some are probably just not aware of, or not well informed about, this service. Unfortunately, many others know about it but apparently don’t consider it important enough to take the time and expend the [...]

  3. Stockpiling Warm Season Grasses

    Less-than-optimum weather conditions, as well as the cost of fertilizer, fuel, and other production inputs are factors that often make it difficult for livestock producers to make a profit.  Providing  nutrition during times when pasture is not available is one of the costliest aspects of producing livestock, so it makes [...]

  4. PASTURES TELL A STORY

    A livestock producer learns a lot about a pasture over time by managing it, but that is not the only way to obtain information about a given field. Often, a great deal can be gained from simple observation, because various plants are more likely to become established and thrive under [...]

  5. KEY HAY STORAGE CONCEPTS

    Providing nutrition when little or no pasture forage is available constitutes the single largest expense associated with most livestock operations. In most cases, hay is the most logical type of stored feed to use. Generally, the less hay required, the greater the cost effectiveness of an operation, and how hay [...]